Electrical Safety

Service Mast Repair: 6 Proven Steps and Costly Mistakes

Service mast repair shown as a labeled anatomy drawing of a residential riser
Key Takeaways
  • Service mast repair ranges from a weatherhead swap to a full one-piece riser replacement, and the damage decides which.
  • DTE accepts only one-piece hot-dip galvanized risers, so a coupled or patched mast usually fails inspection.
  • A 2-inch rigid mast carries 750 pounds of drop tension and allows 30 inches of unsupported length.
  • Budget 500 to 1,700 dollars for mast work in 2026, and more once the meter socket goes with it.
  • Satellite dishes and cable lines bolted to a mast break code and add the wind load that bends it.

Service mast repair covers everything from a cracked weatherhead to a complete riser replacement, and the right scope depends on what actually failed. A bent or pulled mast almost always needs the whole pipe replaced, because DTE accepts only one-piece risers. Fittings on their own can often be swapped.

IB Electric has repaired service entrances across Wayne, Oakland, and Macomb counties since 2002, and our founder, Imad Boussi, has held a Michigan master electrician license since 1997. Masts come to us in two states: leaning after a storm, or quietly rusted through after 40 winters. The repair looks identical from the street. The price and the paperwork are nothing alike.

What Does Service Mast Repair Actually Involve?

A service mast is the vertical steel pipe that carries your service entrance conductors from the weatherhead down to the meter socket. On an overhead service it also holds the drop from the pole, which means it is structural, not just a conduit. Service mast repair therefore splits into two very different jobs.

Replacing the weatherhead, the roof flashing, a bracket, or a clamp counts as parts work, and the pipe stays. Replacing the mast means pulling the conductors, removing the whole riser, and setting a new one. Because the pipe is load-bearing, Section 230.28 of the National Electrical Code requires it to have enough mechanical strength on its own, or braces or guy wires to handle the strain the conductors put on it.

That strain is the thing most homeowners never picture. A service drop pulls sideways on your wall every day of the year, and it pulls harder in ice.

Why Service Masts Fail

Four causes account for nearly every mast we replace, and three of them come down to load the pipe was never sized for. Wind and ice top the list: a loaded drop in a Michigan ice storm can double its usual pull, and a mast already weakened by rust gives way at the roof line. Corrosion is second, because water tracks down the outside of the pipe and sits in the flashing.

Third is added attachments, meaning satellite dishes, cable lines, and antennas bolted to the mast by installers who had nowhere else to go. Fourth is a falling limb, which bends the pipe in a single afternoon. Meanwhile the symptoms are easy to read: a visible lean, a gap at the roof flashing, rust streaks on the siding, or a drip loop hanging lower than it used to.

Electrical mast repair causes drawn as four failure modes on one diagram
Wind load is the common thread behind most service mast repair calls, and three of the four add load the pipe never carried.
🚨 Nothing other than the service drop belongs on a mast. The code bars antennas under Section 810.12, aerial radio and television cables under 820.44(C), and broadband cables under 800.133(B). Every one of them adds wind load the pipe was never engineered to carry.
Pro tip: Check the mast after any installer visits your roof. We have pulled dish brackets off masts three times this year, and in two of those cases the pipe was already leaning.

Once you know what failed, the next decision is whether the pipe itself has to go.

Service Mast Repair or Full Replacement?

Repair the fittings, replace the pipe. That is the rule we work to, and the code backs it. A cracked weatherhead, a failed roof boot, a loose bracket, or a rusted clamp all count as parts-level items, and the riser stays in place. Anything that has bent, pulled, or rusted through the pipe wall means a full replacement instead. The reason is not caution. DTE accepts only one-piece risers on residential overhead services, so you cannot cut off a damaged top and couple a new section on. The code narrows it further: under 230.28(B), conductors may not attach to a mast between the weatherhead and a coupling where that coupling sits above the last support.

So the cheap-sounding fix, cutting the bent top off and threading on a new length, fails on two counts at once. It fails DTE inspection, and it fails the code. Replace the pipe.

Decision diagram splitting a damaged mast into parts-only repair or full replacement
Service mast repair splits here: fittings come off on their own, a bent or pulled pipe takes the whole riser.
DamageScopePipe replaced?
Cracked or missing weatherheadPartsNo
Leaking roof flashing or bootParts, plus roof sealingNo
Loose or pulled bracketParts, plus wall repairNo
Bent or leaning pipeFull riserYes
Rust through the pipe wallFull riserYes
Mast pulled away from the wallFull riser, usually with the socketYes

What Service Mast Replacement Cost Depends On

Three things move the number. Pipe length comes first, since a mast that clears a two-story roof costs more in material and much more in labor than one on a ranch. Access comes second: a mast over a porch roof or against brick takes longer than one on open siding. Third is what else is coming off with it. When the socket is pulled loose too, the permit, the DTE visit, and the inspection cover both, which is cheaper than doing them twice but a larger single bill.

Whatever the scope, the new pipe has to meet numbers DTE publishes rather than numbers your electrician picks.

The DTE Specs Your Mast Has to Meet

DTE sets the riser spec in Michigan, and it is stricter than the code in several places. DTE wants hot-dip galvanized steel and one piece, with rigid or IMC assemblies of ten feet or less run as a single continuous length. Size then sets two limits at once. According to DTE’s overhead service design practices, a 2-inch rigid riser allows 30 inches of unsupported length and carries a maximum load of 750 pounds, while 2.5-inch allows 42 inches at the same 750-pound limit. (DTE Electric, 2024.) Smaller pipe drops fast: 1.25-inch and 1.5-inch allow only 21 inches unsupported, at 440 and 660 pounds. Solid ring conduit supports go with 2-inch and 2.5-inch pipe.

Those two columns matter more than the price difference between sizes. One governs how far the pipe can stand clear of its last support, and the other governs how hard the drop may pull on it before a guy becomes mandatory.

DTE riser specifications for unsupported length and drop tension by conduit size
DTE publishes the numbers any service mast repair has to meet, and they decide the pipe before preference does.
Rigid conduit sizeMaximum unsupported lengthMaximum load
1.25 inch21 inches440 pounds
1.5 inch21 inches660 pounds
2 inch30 inches750 pounds
2.5 inch42 inches750 pounds

When drop tension passes those load values, a back guy in line with the service drop becomes mandatory, and the contractor furnishes and installs it rather than DTE. As EC&M notes, the code itself gives little strength guidance and leaves the arithmetic to the installer, so many local rules simply require trade size 2 rigid metal conduit as a floor. One more detail saves a return visit: leave 24 inches of conductor beyond the service head for DTE to tap.

💡 Ask your electrician which pipe size they are quoting before you compare bids. A 1.5-inch riser is cheaper and legal in some situations, but it carries less than nine-tenths of the load a 2-inch mast does, and it is the first thing to bend in the next ice storm.

Size settles the pipe. Where the drop lands settles the height.

Clearance Heights: Where the Drop Has to Land

Clearance decides how tall the new mast has to be, and the measurement runs to the lowest point of the drip loop rather than to the attachment itself. DTE sets a residential minimum of 10 feet to grade with 12 feet preferred, and caps the attachment point at 30 feet above grade. Driveways follow the same 10-foot floor with 12 preferred.

Patios, porches, and final grade all take 10 feet. Roofs work differently: a garage roof sloped at 4-in-12 or steeper needs 3 feet of clearance, while a shallower roof needs 8. The code runs on the same logic, and EC&M sets out the grade clearances alongside the 230.26 rule that the attachment sit at least 10 feet above finished grade.

Measure before you assume the new mast matches the old one. Driveways get repaved and grade changes, so a drop that cleared comfortably in 1985 can sit short today.

Service drop clearance heights over grade, driveway, porch and garage roof
Clearance is measured to the lowest point of the drip loop, not to the attachment.
  • Grade, patios, and porches. 10 feet minimum to the lowest drip loop.
  • Residential driveways. 10 feet minimum, 12 feet preferred by DTE.
  • Garage roof, 4-in-12 or steeper. 3 feet of clearance.
  • Shallower roofs. 8 feet of clearance.
  • Attachment point ceiling. No higher than 30 feet above grade.
⚠️ If your old mast was short and the drop now hangs below 10 feet, the replacement gets taller. That changes the pipe length, sometimes the pipe size, and occasionally whether a guy is needed. A quote based on matching the old mast is a quote that will move.

There is one more way a mast job can change shape, and it catches people completely off guard.

When a Mast Replacement Becomes an Underground Service

Here is the part no competitor mentions. DTE states on its overhead service page that new, relocated, or upgraded residential services shall be installed as underground residential service laterals at the customer’s expense. A straight repair keeps you overhead. A job that DTE classifies as a relocation or an upgrade, however, can push the whole service underground, which means trenching, a new lateral, and a bill in a different bracket entirely. Where the line falls depends on scope and on your address, so ask DTE before anyone writes the quote, not after the mast is down.

The gap between those two outcomes is not small. An overhead mast replacement is a four-figure job at the lower end. An underground conversion brings trenching across the yard, a new lateral, and restoration of whatever the trench crossed, which is a different conversation with your budget entirely.

Diagram showing when a mast replacement becomes an underground service conversion
The policy nobody warns you about: a service mast repair large enough to count as a new service goes underground.

What most guides get wrong: they treat a mast as a part you swap, like a water heater. In DTE territory the mast is attached to a utility policy. Replacing it in kind is routine. Moving it, raising the service size, or relocating the attachment can reclassify the whole job, and the trenching bill dwarfs the pipe.

⚠️ Ask one question early: will DTE treat this as a repair or as a new service? The answer changes the budget by thousands, and only DTE can give it. Our Michigan permit guide covers how that conversation fits with the city side.

With the classification settled, the work itself runs to a predictable order.

Mast leaning, or power off after a storm?
IB Electric makes the service safe, pulls the permit, and sequences the DTE disconnect and reconnect, so a service mast repair does not leave you coordinating two organizations. See our emergency service or call (313) 274-3588.

How a Service Mast Repair Actually Runs

Service mast repair follows two different paths, and knowing which you are on tells you how long the power stays off. A weatherhead or flashing repair often happens with the service live, in an hour or two, and some cities ask for no permit at all. A full riser replacement is a different animal. Your electrician pulls a municipal permit, DTE is scheduled to disconnect the drop, the old mast and conductors come out, the new one-piece riser goes in with its supports and flashing, the city inspector approves it, and only then does DTE reattach the drop and energize. As ExpertCE notes, the roof penetration needs a flashing boot or another approved detail to stay watertight.

Plan for two to five hours of work and anywhere from two days to two weeks of scheduling, because the permit, the utility, and the inspector each have their own calendar. Storm weeks stretch the far end of that range.

💡 Book the city inspection before the DTE disconnect rather than after the work. Most Metro Detroit inspectors will slot a service repair next business day once they know the power is off, and that single call often halves the outage.

Which leaves the question every quote comes down to.

What Does Service Mast Repair Cost in 2026?

Budget 500 to 1,700 dollars for a mast or riser replacement in 2026, with a national average near 1,100. According to HomeGuide, that is the usual range, with a floor near 300 for simple work and a ceiling around 5,000 on difficult installations. Weatherhead replacement on its own runs 200 to 600 dollars, permits add 50 to 350, and electrician labor sits at 50 to 130 dollars an hour. (HomeGuide, 2026.) Pipe itself is cheap by comparison, at 10 to 20 dollars per linear foot for 2-inch and 20 to 30 for 4-inch. Specifically, labor and coordination carry this job, not materials.

That ratio explains the spread. Two quotes on the same pipe can differ by 600 dollars because one crew expects a two-hour job on open siding and the other has priced scaffolding over a porch roof. Ask what access each one assumed.

Service mast repair cost ranges for 2026 drawn as four horizontal bars
Service mast repair cost in 2026, before any meter socket or panel work is added.
ScopeWhat is includedTypical 2026 range
Weatherhead or fittings onlyParts, no permit in many cities200 to 600 dollars
Full mast and riser replacementOne-piece pipe, supports, flashing, permit500 to 1,700 dollars
Mast plus meter socket after storm damageBoth, plus wall and siding repair1,200 to 3,000 dollars
Mast, socket, and a 200-amp panelService equipment, outdoor disconnect, inspection2,500 to 5,000 dollars

Across the Metro Detroit service repairs we have run, the mast and the meter socket came off together on roughly 60 percent of storm calls, because the same pull that bent the pipe tore the can off the wall. Insurance usually covers storm damage to both, so photograph everything before anyone starts work.

💡 If the mast is failing and the panel is 1970s vintage, price them together once. The permit, the DTE visit, and the inspection are shared costs across the two jobs, and our panel replacement cost guide has the combined ranges.

Storm season is when most of these decisions get made in a hurry, so it helps to know your scope in advance.

The Service Mast Repair or Replace Decider
Three questions to find whether your service mast repair is a parts job, a full riser, or something DTE will reclassify.

Question 1 of up to 3

Not sure whether yours is a parts job or a pipe job?
Send a photograph of the mast from the ground and one of the roof line. We will tell you which service mast repair scope you are looking at, and what DTE is likely to call it, before anyone books a visit. See our residential service or book an assessment.

Frequently Asked Questions

How much does it cost to replace a service mast?

Service mast repair at full riser scope runs 500 to 1,700 dollars in 2026, with a national average near 1,100 and a ceiling around 5,000 on difficult installations. Weatherhead-only work runs 200 to 600. Permits add 50 to 350. The number climbs when the meter socket is damaged too, although sharing one permit and one utility visit keeps that combined job cheaper than two separate ones.

Can a bent service mast be straightened instead of replaced?

No, not in DTE territory. DTE accepts only one-piece risers on residential overhead services, so you cannot cut a damaged top off and couple a new section on. Code adds to that: conductors may not attach between the weatherhead and a coupling that sits above the last support. A bent pipe means a new pipe.

Who is responsible for repairing the service mast?

You are. The mast, the weatherhead, the meter socket, and the service entrance cable all count as customer-owned equipment, so a licensed electrician repairs them at your expense. DTE owns the service wires from the pole and the meter itself, and it disconnects and reconnects around your electrician’s work at no charge.

Do I need a permit for service mast repair in Michigan?

For a full riser replacement, yes. Every Metro Detroit city treats service work as permitted electrical work, and DTE will not energize until the city approves it. Cities handle parts-only repairs such as a weatherhead swap differently, so your electrician should confirm before starting.

How long will my power be off during a mast replacement?

The work itself takes two to five hours. The scheduling takes longer: a permit, a DTE disconnect, a city inspection, and a DTE reconnect all have to line up. Plan for two days to two weeks overall, and longer in the week after a regional storm.

Can I attach a satellite dish or cable line to my service mast?

No. The code bars antennas under Section 810.12, aerial radio and television cables under 820.44(C), and broadband cables under 800.133(B). Beyond the code problem, each attachment adds wind load the mast was never sized to carry, and that extra load is a common reason masts bend in ice storms.

What size should my service mast be?

Two-inch rigid galvanized steel is the usual answer for a residential 200-amp service, and many local rules set it as the minimum. DTE allows 30 inches of unsupported length and 750 pounds of load on 2-inch pipe. Smaller 1.5-inch pipe allows only 21 inches at 660 pounds, which is why it bends first.

When should I call an electrician about my service mast?

Immediately, for any lean, gap at the roof, rust streak, or drip loop hanging lower than it used to. Service mast repair is not something to defer, because the mast sits ahead of every breaker in the house and nothing protects it. IB Electric handles the permit, the repair, and the DTE scheduling. See our emergency service or book an assessment.

Conclusion

Service mast repair comes down to one question: did the pipe fail, or only the parts on it? Fittings get swapped and the riser stays. A bent service mast, a rusted-through one, or a mast pulled off the wall takes a full one-piece replacement, because DTE accepts nothing else. Remember the three things that move the price: pipe length, access, and whether the meter socket comes off with it. Photograph the damage, then call an electrician before you call your insurer.

Get the mast right once, and the next ice storm is somebody else’s problem.
IB Electric sizes the riser to DTE spec, sets it as one piece with proper supports and flashing, handles the permit and the inspection, and sequences the disconnect and reconnect, across Wayne, Oakland, and Macomb counties. Same-day assessment on leaning masts. Book an assessment or call (313) 274-3588.

🌟 The Service Mast Inspection Sheet

Eight things to check from the ground once a year, so a lean gets caught in September rather than during the first ice storm.

Get the sheet →

Need a licensed electrician in Metro Detroit?

IB Electric has powered homes and businesses across Wayne, Oakland & Macomb counties since 2002. Get a fast, honest quote from a master electrician.